Skip to main content
    Pro Reference Trades Suite
    Sign InCreate accountAdminUpgrade
    Arkansas · NEC Journeyman

    Arkansas Electrical Journeyman Practice Exam — Free

    Free arkansas electrical journeyman practice exam. Arkansas currently follows NEC 2020 for electrical work. Each question on this set is paraphrased from publicly-available code summaries with the section cited — confirm the in-force edition with your AHJ. Practice the warm-up set ungated, download a 20-question study PDF, or share your email for the full question bank.

    Adopted code: NEC 2020

    Start the free NEC journeyman queue

    Sample questions

    1. Per Article 100, a device whose purpose is to carry or control electric energy as its principal function (but not consume it) is best described as a:

    1. A. Utilization equipment
    2. B. Device
    3. C. Luminaire
    4. D. Appliance
    Show explanation

    Article 100 defines a Device as a component whose principal function is to carry or control electric energy. Utilization equipment converts electrical energy into another form (heat, light, motion); a luminaire is a complete lighting unit; an appliance is utilization equipment for a specific function.

    Ref: NEC Article 100

    2. 125 V, 15 A and 20 A receptacles installed in a dwelling-unit kitchen serving the countertop surface must have:

    1. A. AFCI protection only
    2. B. GFCI protection
    3. C. Both GFCI and AFCI protection
    4. D. No special protection if more than 6 ft from the sink
    Show explanation

    §210.8(A) requires GFCI protection for 125 V, 15/20 A receptacles in dwelling kitchens (and many other locations). §210.12(A) requires AFCI protection for branch circuits supplying 15/20 A, 120 V outlets in kitchens (and most other living areas). Dwelling-unit kitchen countertop receptacles thus require both.

    Ref: NEC §210.8(A) / §210.12(A)

    3. For a single-family dwelling, the minimum size service-disconnect rating is generally:

    1. A. 60 A
    2. B. 100 A, 3-wire
    3. C. 150 A
    4. D. 200 A
    Show explanation

    §230.79(C) requires a minimum 100 A, 3-wire service disconnect for a one-family dwelling. Smaller services (60 A, 2-wire) are permitted for limited installations (e.g., loads under 10 kVA serving very limited equipment per §230.79(A)/(B)).

    Ref: NEC §230.79

    4. The branch-circuit short-circuit and ground-fault overcurrent device for a single continuous-duty motor is sized using:

    1. A. The motor nameplate FLA
    2. B. Table 430.52 percentages applied to the motor full-load current (FLC) values from Table 430.247–250
    3. C. Always 125% of nameplate amps
    4. D. 300% of locked-rotor amps
    Show explanation

    §430.52: branch-circuit short-circuit/ground-fault device is sized by Table 430.52 percentages applied to the motor FLC value from Tables 430.247 (DC), 430.248 (1Φ), 430.249 (2Φ), or 430.250 (3Φ) — NOT the nameplate FLA. Nameplate FLA is used for overload sizing (§430.32).

    Ref: NEC §430.52 / Table 430.52

    Want the full question bank?

    Drop your email and we’ll send the complete study PDF — every question, answer, and code reference.

    Arkansas FAQ

    Which code does Arkansas use for the journeyman electrical exam?

    Arkansas currently uses NEC 2020. The state licensing board sets the exact exam edition — confirm before you sit.

    Is the Arkansas electrical journeyman practice test really free?

    Yes. The warm-up set is fully ungated (first 5 questions per track). The 20-question study PDF is a free download. Only the full-bank PDF is gated by a newsletter signup.

    How many questions are on the actual Arkansas journeyman exam?

    Most state exams run 80-100 questions over 4 hours, open-book, with a 70-75% pass mark. Exact format is set by the state licensing board (often delivered by PSI, Prov, or Pearson VUE).

    Where can I check Arkansas code amendments?

    Local jurisdictions in Arkansas may publish amendments through the state's building-codes board or municipal codes. Always verify with the Authority Having Jurisdiction before relying on a specific value for design or installation work.